Blog/Build a Workshop Tool Tote That Actually Holds Everything

Build a Workshop Tool Tote That Actually Holds Everything

This article may contain affiliate links. If you make a purchase through these links, we may earn a small commission at no extra cost to you. This helps us keep creating free content.

Build a Workshop Tool Tote That Actually Holds Everything

πŸͺšDisclaimer: This article is for informational purposes only. Woodworking carries injury risks β€” from circular saws and table saws to lathes and routers. Always wear PPE (safety glasses, hearing protection, dust mask), follow manufacturer safety guidelines, keep tools clean and sharp, and never operate machinery when fatigued or distracted. Push sticks, blade guards, and proper grain orientation reduce kickback risk significantly.

Every project starts the same way: the first ten minutes go to wandering around the shop gathering tools. Chisels from the wall rack, a square from the drawer, marking gauge from the shelf, pencils from wherever they rolled. Then halfway through you notice the mallet is still on the bench and make another trip. A tool tote puts everything within arm's reach and goes where you go, bench, assembly table, sawhorses, even out to the deck for an outdoor repair.

The design here holds ten chisels, a small block plane, a combination square, a marking gauge, pencils, a tape measure, and yes, a coffee mug. Because priorities.

Design and Dimensions

The tote is essentially an open-top box with a center handle divider. Two compartments on either side of the handle hold tools vertically and horizontally. The overall dimensions are 18 inches long, 8 inches wide, and 10 inches tall to the top of the handle. These proportions fit the most common hand tools without being so big that it becomes awkward to carry.

Build a Workshop Tool Tote That Actually Holds Everything β€” practical guide overview
Build a Workshop Tool Tote That Actually Holds Everything

The center divider runs the full length and height of the tote, doubling as the handle. It extends 3 inches above the sides and has a hand-grip slot cut through it. This divider also provides structural rigidity, it turns a floppy open box into a surprisingly stiff tool carrier.

One side of the divider gets a row of 1/4-inch holes drilled at an angle for chisels. The angled holes keep chisel handles leaning slightly inward so they do not fall out when you pick up the tote. The other side stays open for larger tools that do not fit in dedicated slots.

Size It to Your Tools: Before cutting any wood, gather the tools you want this tote to carry and arrange them on your bench. Measure the footprint and height you need. The dimensions given here suit a common set of bench tools, yours might be different. A tote that does not fit your specific tools is just a fancy box.

Materials and Cut List

Hardwood scraps are the natural material for a tool tote, and red oak offcuts from a previous project are a typical starting point. Softwood works too but it dents faster and the chisel holes wear out sooner. Avoid plywood for the sides, it splinters at the top edges where you grab the tote and the exposed plies look rough.

Here is the cut list: two side panels at 18 by 6 inches from 1/2-inch stock, two end panels at 7 by 6 inches from 1/2-inch stock, one bottom panel at 18 by 8 inches from 1/2-inch stock, one center divider at 18 by 10 inches from 3/4-inch stock, and optionally one chisel holder strip at 16 by 2 inches from 3/4-inch stock.

Total material is under 3 board feet of hardwood. If you do not have suitable scraps, this is a great excuse to buy a single board of something nice at the lumber yard, you will be looking at this tote every day, so use something you enjoy seeing.

Mill all five panels to final thickness in one session before you cut anything to length. Mixed thicknesses are the most common source of gappy corners on a small box, because a side panel that sits proud of its neighbor by even a shaving shows up immediately in a box joint. If you are working from rough stock, let the boards sit in the shop for a few days after milling and take a final pass before layout so any cupping is removed rather than glued in.

Cutting the Joinery

The box joints at the corners are the most satisfying part of this build. Cut them on the table saw with a box-joint jig, 3/8-inch fingers for the 1/2-inch stock. Box joints are overkill for a tool tote structurally, but they look fantastic and they practice a skill you will use on nicer projects later.

Build a Workshop Tool Tote That Actually Holds Everything β€” step-by-step visual example
Build a Workshop Tool Tote That Actually Holds Everything

Cut a test joint in scrap of the same thickness first and check the fit before touching the real panels. The fingers should push together with hand pressure and no mallet. If they need pounding, the jig's key is a hair too wide and the glue-up will split the end grain instead of closing.

If box joints feel like too much effort, use simple rabbet joints instead. Cut a 1/4-inch deep rabbet on the ends of the side panels and glue the end panels into them. Pin with a couple of brad nails for insurance during the glue-up. Nobody is going to judge your tool tote joinery, it is a shop accessory, not a jewelry box.

The center divider sits in a 3/4-inch dado cut across the bottom panel. This dado anchors the divider and keeps it from shifting when you load up heavy tools. Cut the dado 1/4-inch deep, enough for a solid mechanical connection without weakening the bottom panel.

The Handle Grip: Cut the hand grip in the center divider before assembly. Drill two 1-inch holes about 5 inches apart in the upper portion of the divider, then connect them by cutting out the waste between them with a jigsaw. Round over all the grip edges generously with sandpaper or a 1/4-inch roundover bit, sharp edges on a handle you grab fifty times a day is a mistake you only make once.

Assembly

Dry-fit everything first. The assembly order matters: glue and clamp the box joints at all four corners to create the open box. While the glue is setting, slide the center divider into its dado in the bottom panel, do not glue it yet. Once the box is cured, slide the bottom panel and divider assembly up into the box from underneath and secure with glue and screws from the bottom.

The bottom panel should be recessed about 1/4 inch up from the bottom edges of the side and end panels. This creates four small feet at the corners that keep the tote from sitting in puddles of glue or finish that inevitably accumulate on shop surfaces.

Now glue the center divider into the bottom dado permanently. Add a screw through each end panel into the divider ends for extra strength, the handle takes all the lifting force and a pure glue joint may not hold up when the tote is loaded with ten pounds of tools.

Drill pilot holes for those screws rather than driving them straight into the divider's end grain. End grain splits readily at the edge of a 3/4-inch panel, and a split there is hard to clamp because the divider is already glued into the bottom. Check the box for square across both diagonals while the corner clamps are still on, since a divider set into a racked box will lean and the chisel strip mounted to it will lean with it.

Adding the Chisel Slots

The dedicated chisel storage is what elevates this from a generic tote to a genuinely useful shop organizer. Take the 3/4-inch chisel holder strip and drill holes sized to your chisel handles, typically 1/2-inch for bench chisels. Drill them at a 10-degree angle leaning toward the center divider.

Mount this strip inside one compartment, attached to the center divider about 2 inches down from the top. The angled holes hold chisel handles securely but release them easily with a slight pull upward. Five slots on the 16-inch strip is a practical layout, which covers a standard set of bench chisels from 1/4 inch to 1-1/4 inch with room between handles for your fingers.

Drill the strip on the drill press with the table tilted to 10 degrees, before it goes anywhere near the tote. Drilling at an angle freehand wanders, and a hole that ends up steeper than intended will let the chisel handle foul the opposite wall. Test one hole against your largest handle first, because handle diameters vary between brands even within the same nominal chisel width.

On the opposite side of the divider, screw a short strip of leather to the inside surface as a simple tool loop. This holds a marking gauge, small square, or scratch awl flat against the divider. A piece of scrap leather from an old belt works perfectly, two brass screws at the top and bottom, with enough slack to slip tools behind it.

Customize Ruthlessly: The whole point of building your own tool tote is that it fits your tools and your workflow. If you never use chisels, skip the chisel holder and add a wide pocket for a hand saw. If you are a carver, add dowel pegs for hanging gouges. Make it yours, not a copy of someone else's tote that holds tools you do not own.

Finishing the Tote

Two coats of boiled linseed oil (BLO) and nothing else is the right finish here. BLO is cheap, easy to apply, and it handles the inevitable dings, scratches, and glue drips that come with shop life. When the tote looks tired, wipe on another coat and it looks new again in ten minutes.

Some people leave shop accessories unfinished, which is fine, but the BLO helps the wood resist absorbing moisture from wet tools and fresh glue. It also makes the grain pop, which is a reasonable thing to want from an object that sits in view of the bench all day.

Skip polyurethane and skip lacquer. A tool tote gets banged around, dropped on concrete, and loaded with sharp objects. A film finish will chip and flake within weeks and look worse than bare wood. An oil finish just patinas with age and gets more character over time.

Spread oily rags flat or submerge them in water before you leave the shop. Boiled linseed oil cures by oxidation and generates heat as it does, and a balled-up rag in a bin is the standard way a finished project ends up causing a fire.

What the Tote Changes Day to Day

The gain is not storage capacity, it is the elimination of the wandering-around-gathering phase at the start of every session. Ten frequently used tools stay together, stay organized, and travel as one unit. You pick up the tote, carry it to wherever the work is happening, and start.

The other benefit is less obvious: the tote forces you to identify your actual essential tools. There is only room for about a dozen items, so you have to decide what really matters, and the tools that keep getting swapped back out are the ones you were never really reaching for. That exercise alone is worth the three hours it takes to build the tote.

If you build only one version, build it around the tools you reach for in the first ten minutes of a typical project, not around the tools you own. Measure those, size the compartments to them, and leave the chisel strip removable with two screws so the layout can change when your work does.

Published by the Woodworking Workshop editorial team. Published November 21, 2026.

Editorial responsibility: see Imprint.

Spotted an error or have something to add? corrections@thewoodworkingpodcast.com

Share with fellow woodworkers:
projectsshop organizationbeginner-friendlyhand toolsquick builds
πŸ“–

Explore more

All articles on Woodworking Workshop β†’

πŸͺ“

Workshop Mail

New project plans, tool reviews, and woodworking tips β€” delivered weekly to your inbox.

🎁 Free bonus: Beginner's Tool Checklist (PDF)

You might also like

Comments (0)

Leave a comment

Comments are reviewed before publishing.